Philips, Grundig, Millplus Information Collaboration

Can you please send me the download link, think it should work for my DMU70V.

Hello, I'm sorry I entered the wrong email address here is the correct one: [email protected] . Sorry again.

DB3DCNC said:

Can you please send me the download link, think it should work for my DMU70V.

Click to expand...

I have sent you PM.

Hello, I want to ask where the link would be sent. I haven't received it yet, please send it again. [email protected]
Thanks.

Regards to all
I need help with my machine DMU 80P, year 1999. MILL PLUS nc unit with simodrive 611. I have a B74 error on the DDC 2 card. It was tested by replacing it with another card and the alarm moved to another axis. Is it possible to move the B axis with parameters and cables to another channel, since the fifth axis is not mounted on the machine?

Thanks

[email protected]

On the DMU 5V MillPlus 1996 machine (5-axes), an error O 208 pops up after loading. Probably the information on the hard disk is damaged . I ask for help. [email protected]

Slava said:

On the DMU 5V MillPlus 1996 machine (5-axes), an error O 208 pops up after loading. Probably the information on the hard disk is damaged . I ask for help. [email protected]

Click to expand...

Ihave send you email with my hard drive image it is V4.00 MillPlus from my DMU50evo

Slava said:

در دستگاه DMU 5V MillPlus 1996 (5 محور)، خطای O 208 پس از بارگیری ظاهر می شود. احتمالا اطلاعات هارد دیسک آسیب دیده است. من کمک می خواهم. [email protected]

Click to expand...

Hi slava.
I think you should contact the professional team that runs https://www.pgh-controlparts.com.
Be with them, I also had a big problem with the Philips controller which was fixed with the site instructions.

have one Deckel DMU 80 with MillPlus in my shop. I reload parameters after a BIOS battery problem and now the machine is up and running, but when I try to start spindle M3 S1000 it gives this error: E102 prog. “S”˃ max. diameter of tool

Machine accept only maximum 18 rpm for the spindle.

My machine doesn’t have any tool changer and there is no reference for speed on tool table or some sort of setting.

I don't have manual or any error list to check what is the meaning of this error.

Do you think you can help with any advice?
Thank you,

HI, happy new year to all! i have problem with dmu50v, we bought maschine with software v420 but configuration of the maschine is y axis as main axis-, so y and z axis are switched. when y switch on control board is pressed on screen is correct but z axis move whichever configuration we try stay the same, shud we install new software or is possible otherwise. or some other maschine back up. thanks for help!

I was having problems with my 2000 DMU50V with Millplus 4.0. X53, X04, Z04, and other errors related to the E stop chain usually when opening or closing the door. I received some advice from another member and replaced some of the Estop relays in the cabinet and some of the relays on the DDC boards. That helped a bit and I was able to make parts but occasionally still had to stop and restart to keep the machine going. A few weeks ago, the control stopped at boot with an M71 error (no power to PG1220). Tried to restart but the screen was blank, no power on the PG1220. Power supply for the PG1220 was dead. I did see evidence that at some point, the 5 mosfets were replaced along with a few other components. Ive had the machine since 2015 so it was sometime before that.

Power supply is a Philips PE1927/71. Looked on ebay and there were a couple used units in Europe and Indonesia for $1400 or more. I searched around a bit and saw an identical power supply designated as a PE 1927/23B. It was only 69$ so I bought both that the seller had for sale. I looked it over upon arrival with an electrical engineer buddy of mine and he confirmed it was the same except for the voltage input jumper, which was set to 120VAC on the $69 PS. Installed it, checked the voltage outputs on the test points of the PG1220, and so far Ive had no errors at all after making a few parts. Might be helpful to know as it seems like a common problem with these older DMG machines. Im sure it was just the fets that were bad but it worked out in the end.

If anyone has a schematic for these supplies Id like to get a copy. I searched far and wide and didn't see anything online. Philips sold their PS division to Cherokee at some point, and Cherokee merged with another company so its probably all lost.

The problem with the PE1927/xx power supply is a well known problem. The 1927 etc. P/S components have reached their end of life and are VERY DANGEROUS still to be used in the control. The Mill Plus has no over temperature protection, so if the P/S overheats, IT WILL JUST BLOW UP AND BURNING HALF THE CONTROL MODULES. We had several customers, which had the P/S repaired by some local shop, only to having it fail a few month later, taking half the control with it. Sometimes we could repair it, if we had the parts, but the bill was exceeding Euro 15000. The alternative was to scrap the machine .So please be sure you know what you are doing. We at ROBTEC don't even test the repair-controls with this P/S at all, but replace it with a new one.