Largest Manufacturing Technology Community on the Web
Stay Connected:
Search results
-
Index B-axis to 45°, but not rotate coordinates.
Hi! (Using Mazatrol) So I have a situation where I have to index the B axis to 45° and mill a slot perpendicular to the Z axis at B0°. However, the machine automatically uses G68 to line up with the tool at a given angle. So, I want to negate this effect so that I can program easier. As of...- MazatrolMatrix
- Thread
- Replies: 0
- Forum: Mazak
-
-
Explain modified flank indeed threading
So I have a little difficulty visualizing what's actually happening here with a cnc machine. Is the Z starting point of the threading cycle starting further in each time so that the back edge gets clearence after the initial cut?- MazatrolMatrix
- Thread
- Replies: 8
- Forum: CNC Machining
-
Mazatrol Nexus - EIA - Virtual Y-Axis Interpellation?
It is the same as ViktorS says on matrix and matrix 2, unsure about nexus but it is probably the same. G13.1 is polar off Edit: Our Nexus is the same- MazatrolMatrix
- Post #5
- Forum: Mazak
-
Integrex B-Axis center of rotation (E-410)
For others it may be, I thought I'd make a guide with pictures and everything when I have the time. Along with a step 1. xx 2.xx and so on. Mostly for the company I work for but might as well post it here.- MazatrolMatrix
- Post #11
- Forum: Mazak
-
Integrex B-Axis center of rotation (E-410)
No, it’s ok. I know how it is done. Thanks- MazatrolMatrix
- Post #9
- Forum: Mazak
-
-
Integrex B-Axis center of rotation (E-410)
As simple as it may be when you know how it's done, your explanation there is not quite correct. Edit: The picture is correct though.- MazatrolMatrix
- Post #6
- Forum: Mazak
-
Mazatrol Nexus - EIA - Virtual Y-Axis Interpellation?
G2.1 is for spiral interpolation which is an option- MazatrolMatrix
- Post #2
- Forum: Mazak
-
Integrex B-Axis center of rotation (E-410)
I solved it. Turns out that like everything else it isn't really difficult. Just that the information regarding how it's done is scarce or people are unwilling to share it.- MazatrolMatrix
- Post #3
- Forum: Mazak
-
Integrex B-Axis center of rotation (E-410)
Hello! So we are trying to adjust the rotation center because Z0 is different in B0 vs B90 by 0.2mm. I know you adjust by manipulating BA61 and BA62 parameters. But how do you go about in getting the right amount to shift in each parameter? We have two indicators set up to Zero in both axis in...- MazatrolMatrix
- Thread
- Replies: 11
- Forum: Mazak
-
Mazatrol Nexus - Shape Exceeds Material Size - Why?
Your contour doesn’t make any sense to me. You use bar back unit, but the first line is like a regular bar out unit. You start from the wrong direction that is. Then you go… you are using some special tool to make a weird recess of some kind or..?- MazatrolMatrix
- Post #2
- Forum: Mazak
-
how do people make those super sharp corners on molds?
I can’t see it as external either. In fact, I can’t even imagine a way to interpret that as external at all. Not a good sign.- MazatrolMatrix
- Post #21
- Forum: CNC Machining
-
How hard is CNC Machining?
I think that studying math and learning how to calculate stuff yourself, not depend on software all the time, improves your ability to think in all areas and gives you more brain power to work with.- MazatrolMatrix
- Post #29
- Forum: CNC Machining
-
Tool path check excluding noseR.
Hello, (Edit: it’s a Matrix 2 control) So on the tool path check the machine excludes the nose radius of our tools from the programmed value in the position display. So for example Z2.0 in the program Will read as Z1.6 in the position display during tpc if using a tool with nose radius 0.4...- MazatrolMatrix
- Thread
- Replies: 0
- Forum: Mazak
-
Decelerate spindle start? (E-670)
Hello, I never went that way. I changed parameter SA91 on Our Integrex. It’s in milliseconds and it’s the time it Will take for the spindle to reach max rpm. So if from 0 to 100 takes 4 seconds with SA91 at 0, it will take 9 sec if you put in 9000. It’s a Matrix 2 control though so Probably...- MazatrolMatrix
- Post #5
- Forum: Mazak
-
Matrix Nexus - Change Max RPM mid Program?
Haha I’ve read through the parameter manual 100s of times I think 🙃 everything is always so ultra complex with Mazaks.. at least with Mazatrol. Nice to see another Swede btw.- MazatrolMatrix
- Post #13
- Forum: Mazak
-
C axis interpolation accuracy (INTEGREX)
Yes.. Precisely, it's very weird. It could be a programming error of course but the points are derived from cad file so I don't know. I'll try looking for the program tomorrow.- MazatrolMatrix
- Post #6
- Forum: CNC Machining
-
C axis interpolation accuracy (INTEGREX)
I-400, E-410H and J200. controlls would be Matrix 2, 1 and nexus. It was on center. Done with Mazatrol. Feedrate.. well, various, the phenomenon seems to occur regardless. The out of round was per quadrant I think. So each quadrant was different. Chuck size I'm not really sure, 300mm and...- MazatrolMatrix
- Post #3
- Forum: CNC Machining
-
C axis interpolation accuracy (INTEGREX)
So we have a few jobs coming up that will require milling in XC plane with pretty close accuracy. I have tested the geometric accuracy in the past by milling a circle (boss) on our machines. And the boss would then have diffierent radius all around it, afair it would be out of round by up to...- MazatrolMatrix
- Thread
- Replies: 8
- Forum: CNC Machining