What's new

Search results

  1. J

    OT- bait for mouse traps?

    I have used varying size pieces of hot dogs depending on the size of the trap as bait. Pretty effective at attracting mice and rats.
  2. J

    Can anyone tell me what happened to this jumper cable?

    ^^^^^^^^^^ My vote is rodent damage to the insulation which opened the door for the cable to corrode.
  3. J

    Table saw - single phase motor burnt out

    In my humble and non-expert opinion, the windings look like toast. I would be looking to have a motor shop rewind it or find a replacement.
  4. J

    K.O. Lee Workhead advice

    The many accessories that came with my K.O. Lee B960 Grinder have B&S 11 tapers and a removeable B&S. 11 to 5C adapter. I learned that from the members here including Michiganbuck and I appreciate it. Joe
  5. J

    Elliott Tool Grinder #5

    Lol, I can say the same thing for most if not all of my machine acquisitions. Enjoy it.
  6. J

    Advice on how to make a part for K.O. Lee T&C Grinder

    Hi Johnny, so sorry to hear about your wisdom teeth issues. I'm wincing just thinking about it.... The timing could not have been worse not that there is ever a good time it. In the grand scheme, my issue is/was insignificant. With the help of some very gracious people on this forum, I was...
  7. J

    Advice on how to make a part for K.O. Lee T&C Grinder

    Thanks again for all your help. Joe
  8. J

    What size tapered reamer is needed for a KO Lee grinder?

    Hi Steve, yes, they are definitely tapered. I followed the advice of Michiganbuck and ground a regular reamer to the proper sized tapered reamer. No measuring just trial and error until I got it right. I have another thread about the part I had to make (hack) to replace the original part...
  9. J

    Advice on how to make a part for K.O. Lee T&C Grinder

    Hi Ken, Thanks for your input, your insight on clamping a flat bar to the rotary table would have been a big help to me. As I mentioned in a previous post, I wound up hacking a part using a band saw, angle grinder and bench grinder. Not my best work but it functions and considering the part...
  10. J

    What size tapered reamer is needed for a KO Lee grinder?

    Thanks for your help, I think I will attempt to modify a reamer as Michiganbuck suggested. Joe
  11. J

    What size tapered reamer is needed for a KO Lee grinder?

    Again, I thank you so much for your guidance...
  12. J

    What size tapered reamer is needed for a KO Lee grinder?

    Thanks for your help. Joe
  13. J

    Advice on how to make a part for K.O. Lee T&C Grinder

    Thanks much, you're too kind and I appreciate it. #5 tapered reamer it is.... Joe
  14. J

    What size tapered reamer is needed for a KO Lee grinder?

    Hand push but that's after many years of use and abuse. As always, thanks for taking the time to share your expertise and help someone like me on the other end of that spectrum. Is the reamer you linked to a tapered reamer? Doesn't appear to but heck, maybe I'm missing something which is a...
  15. J

    What size tapered reamer is needed for a KO Lee grinder?

    Silly me, I did not think to look there. Thanks, Joe
  16. J

    What size tapered reamer is needed for a KO Lee grinder?

    The next step in making the new part for my K.O. Lee Grinder is to drill the tapered holes for the table locks. I believe a tapered reamer is what I need and since I will need to purchase one, I am hoping to confirm the size I need. The table lock tapered pin (photo below)is .794 inches long...
  17. J

    Advice on how to make a part for K.O. Lee T&C Grinder

    I appreciate those of you who took the time to respond to my request for help so very much. Considering what the part actually does and knowing that my options were somewhat limited, I decided to hack a new part. Yes, it's a hack job but the resulting part is exponentially better than the one...
  18. J

    Advice on how to make a part for K.O. Lee T&C Grinder

    Thanks, Bob, I don't have CAD nor the skills to use it if I did. Even after identifying the radius, how would you go about cutting it on manual machines? The outside radius I can cut on the bandsaw but the step which is also has the same radius is what has me puzzled. Thanks again, Joe
  19. J

    Advice on how to make a part for K.O. Lee T&C Grinder

    Good Morning, All, I am moving forward cleaning and repairing my recently acquired K.O., Lee B960 T&C Grinder. I came a cross a part that locks the swivel table down that is cracked and was some what repaired. Adise from it being cracked some of the holes for the table locks are also cracked...
  20. J

    FS: Skoda MT5 live center, Procunier #3 tapping head collets, super spacer index plates and NEW Bison 8" backplate blank for threaded chucks

    I did a search using the part number Matt provided. The specs that came up are as follows, I hope it helps: Description: 8 1/4" Bison Unfinished Back Plate A (Backplate Diameter): 8 1/4" Hub Diameter: 4" Through Hole: 1 3/16" Overall Depth: 2 3/4" Thickness at Perimeter: 1 1/8" Stay well, Joe
Top